Equipment Category: Rewinders

Used 108” Face Cameron Slitter Re-Winder, Model 458 2-drum slitter. Approximately 108″ working width. Driven by a 60 HP DC motor and drive. 60” OD shafted rewind capacity. With weighted rider roll, manually actuated shear slitters, roll ejector, (1) rubber covered bowed roll and (1) steel bowed roll, roll kicker.

Cells mounted on the winder for tension control. Rated for approximately 1500 FPM.

Used (still running) 169″ (4.3M) Wide Valmet Winbelt Rewinder. New in 1995 and designed to run a Variety of paper from: coated offset paper and a Basis weight range of 70-150 g/m2.
Additional Details as follows:
– Design Speed at Speed: 2000 m/min. with computerized acceleration and deceleration at 0.6 m/s2
– Emergency braking: 1,3 m/s2 and tension: 1040 N/m
– Max. diameter 2000 mm.
– Trim width range from 3.7 to the narrowest width of 152 mm.
– Slitting blades: 13
– Material: Precision Tooled Steel
Cut-off Width: max. 100 mm., Min. 20 mm.
– Section winding: max. diameter of 1500 mm.
– Sleeve for winding: 70, 76, 120 and 152 mm.
Automatation:
– Control: Windcontrol
– Set of knives (format): Windposit
– Troubleshooting: Windhelp
– Software Update: Windcomm.
Was fully modernized 2005 and now includes a PLC, drive operational control,
traffic control equipment, documentation, and energy accounting.
Does not include MCC (specification document available for repurchase).

Used and Fully Rebuilt 192″ (4.9M) Wide Jagenberg Rewinder Type 51-15
Originally designed for paper with grammage of 55-180 g/m2,
Re-engineered to improve the density of processed paper up to 500 g/m2.
Design speed of 2000 m/min working with paper machine speeds running at 650-800 m/min.
Includes Beloit-Lenox Autotrim Slitters with 12 pairs of knives (1987)
The maximum width 4,900mm with a maximum drum diameter of 2600 mm (30000 kg rolls).
Right-hand driven machine. Unwind stand has an electric tension control system with loading cells.
Also includes a system for Quick-Changing of the Shafts. Shaftless, motorized unwind.
Rebuilt in the 1990s with an advanced automatic control system, tension control, and (rider) shaft for winding density. Pneumatic lowering of the table and all the necessary safety features included.
Built to meet and exceel North American/European standards.

Rebuilt History:

1987 – the new automatic cutting Beloit Autotrim
1991 – Transmission Flender
1991 – The new drive shaft ABB
1991 – (reel holding device) fixture

SPECIAL NOTE: This winder is currently being used as a backup machine and can be demonstrated running with the actual production. It is in EXCELLENT condition and excellently maintained.

Used 196″ (5.OM) Trim OverMeccania 2 Drum Rewinder
New in 1978 and Rebuilt by Talleres Gorostidi in 1986
New Drive System installed in 1999
Max. Speed: 1200 MPM.
Winding Drums 650mm. Diam.
Max. Unwind Diam. 2500mm.
Max. Finished Roll Diam. (without axis): 1500 mm.
Completes Set of SSpares Included



B-10 REWINDER

Comparable to a Beloit Model L with the Engineering of a Jagenberg Vari-Dur

1) TYPE : 2 DRUM SURFACE WINDER
2) PAPER GRADE : PRINTING & WRITING PAPER
3) BASIS WEIGHT : 60 ~ 250GSM
4) DIAMETER OF UNWINDER : MAX 2,000MM
5) DIAMETER OF REWINDER : MAX. 1,500MM
6) WEB WIDTH : MAX. 2,500MM
7) DESIGN SPEED : 1,800M/MIN
8) NUMBER OF SLITTER : 6PCS
9) MIN. SLITTING WIDTH : 260MM
10) DIAMETER OF PAPER CORE :

ID 76MM

JAGENBERG VARI-STEP 43-15 WINDER and Type 24v Reel Spool Unwind Stand (Single Spool)

History: The winder was installed new in 1995 and ran for two years until the machine was decommishened in 1998.

The winder was left in place until 2010 at which time the mill purchased a new winder. The Jagenberg winder was disassembled and stored indoors at the mill’s storage facility.

Specifications:

Nominal Width: 145” / 3.68m

Maximun reel Spool Dia. 144” / 3.65m

Maximum Slit Diameter: 60 “ / 1.5m

Number of Slitters: 5

Speed: 5,000 FPM

 

NOTE: The unit does not include the drives, process contol panels or core chucks. The drive system that was on the unwind was essentially obselete technology and therefore was not brought back with the winder

Used 54″ Dusenbery Converting Systems Model 614-FP, Slitter Rewinder.
Includes a Model 863-WH Single Shafted Unwind stand
54 Dusenbery Slitter Rewinder with Unwind Stand


Used 98″ (2.48M) Wide Cameron Rewinder for Printing & Writing Grades
Later Model, With 4 Shear Cut Slitter Knives
Includes Drive, Control Panel and Several Reel Spools and Overhead Crane