Equipment Category: Pulpers

Used #2 Black Clawson Hydrapulper Drive

The Unit was Opened, Drained of Oil and Inspected

IT is in Very Good Condition

Beloit-Jones Tri-Dyne Pulper Model 5220
12′ Diameter X 7′ Deep for Continuous Operation
Driven by a 400HP 3/60/230/460V Motor
Includes Pump, Valving and Associated Piping
Still Installed and in Very Good Condition


Used 137″ (3.5M) Black Clawson Hydrapulper

High Consistency Operation & Stainless Steel Construction

In Excellent Condition

Black Clawson Hydrapulper

18′ Dia (5.4M) Black Claswon Dual High/Low Consistency Pulper
New in 1998 for a rated capacity of 50m3, 100 TPD
Height: 3335mm and a Basic Vokes Rotor of 1708mm Ø
The unit was originally a low consistency batch pulper
designed to work in batches at (5 – 6%) at a pulping time of 20-30 minutes.
Modified with a 2000mm by 1708mm Ø Helical Rotor Attchment for the High Consistency Conversion
High C onsistency Rating is 10 – 12%. All Stainless steel Aisi 316 Construction with
a 360KW – 3000V Motor. The Unit has been recently dismantled and stored in seller’s yard.
Black Clawson Hi-Lo Consistency Pulper

One each Black Clawson Hydrapurge (pulper scavenger)
Model 950 for continuous operation with a 24” diameter rotor.
The unit was new in 1997. The unit is in excellent condition.
Still installed and requires removal and power-washing clean.
Mill will assist with that and Drawings are also available.
Black Clawson Hydrapurge-Size 3 Detrasher (Poire)
Used and Fully Rebuilt to New Condition
Includes Spare Extraction Plate and Rotor

USED AHLSTROM 250/300 T/D DRUM PULPER, 10′ DIA X 30′

STEEL CONSTRUCTION WITH A 21′ STAINLESS STEEL SCREENING AREA

300HP, 2300 VOLT 1200 RPM MOTOR

INCLUDES AGITATION TANK AND (2) PROCHEM AGITATORS

8″ X 6″ GOULDS 3175 STAINELSS STEEL PUMP.

EXCELLENT CONDITION

Drum Pulper Layout-500 TPD
Used AHLSTROM DRUM PULPER Ahlstrom Model FF-375 EXT
This is a Complete Line with a Rated Production for 350-500 ADMT/DAY
Using an OCC Furnish / Application: Corrugating Medium

This Ahlstrom drum pulper with waste paper sorting line,
Conveyor System, Stainless Steel tanks, etc.

all in “almost new” condition – purchased new and used
for only a short time for taking in recycled cardboard and paper to make corrugated cardboard medium. Mill stopped production in 2003.

More Detailed Description: Fibreflow Drum Pulper System:

Ahlstrom Model FF 375 EXT, complete with inlet chute, pulping zone, screening zone, shower hood, screen-plates, and bottom vat.

The stainless steel inlet chute for introducing the furnish into the drum is complete with feed dilution water connections, Teflon seal and a support stand. The seal area is equipped with a drip pan.

The drum is mild steel with an inner diameter of 12.3 feet and a length of approximately 103 Feet Long. Included in the design of the drum are lifters, breaking segments, and flow control plates.
The reject end consists of a cone and splash plate. Machined cast iron support rollers are mounted on spherical roller bearings. They are
completely assembled on fabricated adjustable bases. A conical guide roll of cast ductile iron is mounted on tapered roller bearings and is completely assembled on a fabricated adjustable base.

The screening zone of the drum is located between the 304 stainless steel shower hood and bottom vat. The shower hood is complete with a dilution water shower, associated manifold and valves. Dilution distribution is controlled with hand valves. Screen plates are mild steel with three (3) sections of step drilled holes. First section stepped 8mm to 10mm diameter; second section stepped 7mm to 9mm; the third section stepped 6mm to 8mm diameter. The screen has a 30% open area.
More Information Available Upon Request